Measurement-computing WaveBook rev.5.3 Manuel d'utilisateur Page 131

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 154
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 130
WaveBook/512A, /516, /516A, /516E 897895 Specifications 8-1
Specifications 8
Specifications - WaveBook/512A
General
Warm-up: 30 minutes to rated specifications
Environment
Operating: 0° to 50°C, 0 to 95% RH, non-condensing
Storage: -20° to 70°C
Power Consumption: 1.4A max @ 15 VDC
Input Power Range: 10 to 30 VDC
Input Power Fuse F201: 4A MINI ATO, see ch. 9
Vibration: MIL STD 810E
Dimensions: 285 mm W x 220 mm D x 45 mm H (11” x 8.5” x 1.75”)
Weight: 1.5 kg (3.3 lbs)
Analog Inputs (18° to 28°C)
Channels: 8 differential, expandable up to 72 differential
Connector: BNC
Resolution: 12 bit
Ranges: Unipolar/bipolar operation is software selectable via sequencer
Unipolar: 0 to +10V, 0 to +4V, 0 to +2V
Note: No unipolar mode is available when a WBK11A, WBK12A, or WBK13A is installed.
Bipolar: ±10, ±5V, ±2V, ±1V
Maximum Overvoltage: ±35 VDC
Input Bandwidth: DC to 500 kHz
Input Impedance
Single-Ended: 5M Ohm in parallel with 30 pF
Differential: 10M Ohm in parallel with 30 pF
Accuracy: ±1V to ±10V: ±0.03% of reading; 0.012% of range
Input Noise: <1 LSB (RMS)
Total Harmonic Distortion: -70 dB typ
Signal to Noise and Distortion: -70 dB typ
CMRR: 70 dB typ; 60 dB min; DC to 20 kHz
Anti-Alias Filter
Type: 5-pole Butterworth; 20 kHz low pass software enabled
Note: No unipolar mode is available when a WBK11A, WBK12A, or WBK13A is installed.
PGA Filter
Filter Type: 20KHz low pass, Butterworth, 5-pole filter
Triggering
Channel 1 Analog & Pulse Trigger
Input Signal Range: -10 to +10V
Bandwidth: 1 MHz
Latency: 300 ns
Multi-Channel Analog Trigger (up to 72 channels):
Range: Selectable per channel to input range
Latency: 2 µs/channel, plus 4 µs maximum
TTL Trigger
Input Signal Range: 0 to 5V
Input Characteristics: TTL-compatible with
10K Ohm pull-up resistor
Latency: 300 ns
Software Trigger
Latency: 100 µs typical
Pulse Trigger Input
Input Signal Range: ±5V
Input Characteristics: 75 Ohm
Input Protection: ±10V maximum
Minimum Pulse Width: 100 ns
Maximum Pulse Width: 0.8 sec
Latency: 300 ns
Note: Specifications are subject to change without notice.
Vue de la page 130
1 2 ... 126 127 128 129 130 131 132 133 134 135 136 ... 153 154

Commentaires sur ces manuels

Pas de commentaire