Measurement-computing LogBook Series Manuel d'utilisateur Page 43
- Page / 222
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
QS360-10 LogBook/360 Quick Start Guide
Testing the Hardware
Before testing LogBook/360:
a) Verify the device has been properly installed.
b) Make sure the communication cable (serial or parallel) is firmly in place to the proper ports.
c) Verify the device is powered-on.
Testing the LogBook/360 device might cause the system to hang. If test results are not
displayed within 30 seconds, or if the system does not respond properly do the following:
Reboot the system.
Upon power-up, re-enter the LogBook Configuration.
Ensure the configuration settings are correct. Change the settings as applicable.
To begin the test, click the Test button. Test results should be displayed within a few seconds.
Test results indicate if the device is online (properly connected, powered on and ready to transfer the data)
or offline. If the device is online, Performance Test will display Download and Upload speed rates. These
rates represent the maximum speed at which downloading and uploading files can be performed. Actual
transfer time will depend on channel configuration and the size of the transfer.
Acquisition Configuration
An acquisition is configured using LogView on a PC and then stored as an acquisition setup file on a
PC-Card. The PC-Card may be in an attached LogBook/360 or in the PC to be later manually transferred to
an unattached LogBook/360. The system’s DBK cards are listed; the scan sequence is defined; the trigger
conditions are specified, etc.
Reference Note:
Configuring the acquisition is described in the LogView section of the user’s manual PDF.
- LogBook/300 & /360 1
- Manual Layout 5
- Table of Contents 7
- Device Menu…… LV-48 9
- Tools Menu…… LV-51 9
- Indicators Menu…… LV-55 9
- LogBook Basics 11
- Front and Rear Panels 12
- Highlight of Features 13
- LogBook/300 Block Diagram 14
- LogBook/360 Block Diagram 15
- Operational Features 18
- Communications 20
- Triggering and Scan Timing 21
- Scan Rate Limitations 21
- Acquisition 23
- Data Storage and Retrieval 23
- General 25
- A/D Specifications 25
- Analog Inputs 25
- Triggering 25
- High-Speed Digital I/O 26
- Frequency/Pulse Counter 26
- Frequency/Pulse Generator 26
- Sequencer 26
- General Purpose Digital I/O 26
- Before you get started 27
- QS300-3 28
- CAUTION 29
- Hardware Configuration 29
- QS300-5 30
- Testing the Hardware 32
- A Note about Calibration 33
- Software Installation 34
- WARNING 35
- Setting Up the Card Drawer 36
- QS360-5 38
- Card Drawer Setup 39
- System Expansion 4 45
- What are DBK Options? 46
- ED7B55484273 47
- Considerations 48
- Mechanical Setup Options 49
- P1 – Analog I/O 51
- P2 Digital I/O 52
- DBK Basics 55
- Introduction 55
- /100 /200 Series 56
- 967794 DBK Basics, pg. 3 57
- 967794 Daq Systems 58
- DBK Identification Tables 63
- Analog Signal Conditioning 64
- 967794 DBK Basics, pg. 11 65
- Power Supply DBKs 66
- 967794 DBK Basics, pg. 13 67
- (see Notes 1 and 2) 68
- On a DBK34 and DBK34A 68
- 967794 DBK Basics, pg. 15 69
- Power Requirements 70
- DaqBook/2000 Series Devices 71
- Power Requirements Table 71
- 967794 DBK Basics, pg. 19 73
- This table is continued 74
- Additional Reading 75
- LBK/COM/422/485 78
- Hardware Description 80
- LBK1 Installation 81
- Remote LogBook Terminal 82
- Main Menu 82
- ***** 82
- LBK1 Menu Map 83
- LBK1 - Specifications 84
- LBK2 - Specifications 86
- Serial Input Fundamentals 90
- Capabilities and Limitations 90
- Installation and Setup 91
- Configuring an Acquisition 92
- Configuration Setup Overview 93
- Format String Reference 96
- Channel Type Selection Table 98
- GPS Examples 98
- LogBook/GPS - Specifications 101
- What is a Modem? 103
- Step X.2 – Set up the Modem 106
- Step Y.2 – Set up the Modem 114
- Frequently Asked Questions 120
- Overview 123
- CE Standards and Directives 123
- CE Compliance 8 123
- Safety Conditions 124
- DBK41/CE 125
- ED7B55484273 127
- Understanding LogView 127
- Modes of LogView Operation 128
- 989592 LogView LV-3 129
- 989592 Software Reference 130
- Software User-Interface 131
- 989592 LogView LV-7 133
- File Management 134
- 989592 LogView LV-9 135
- Procedures 137
- Using an Attached LogBook 138
- 989592 LogView LV-13 139
- Using LogBook “Unattached” 140
- Simple Data Logging 140
- 989592 LogView LV-15 141
- Setting Up DBK Cards 142
- Using Multiple Timebases 143
- 989592 LogView LV-19 145
- 989592 LogView LV-21 147
- Using Exception Capturing 149
- Menu Descriptions 150
- File Menu 150
- Save As 151
- Download 153
- Configuration Report 153
- ED7B55484273 154
- View Menu 155
- 989592 LogView LV-31 157
- 989592 LogView LV-33 159
- 989592 LogView LV-35 161
- 989592 LogView LV-37 163
- ~ AND-expression 165
- & 10010000 = = 10010000 165
- Example 1: P1_CH14 > 23 166
- Example 3: P1_CH14+P1_CH15 167
- Example 4: P1_CH14*2 167
- Acquisition Configuration 168
- 989592 LogView LV-43 169
- Preferences 171
- Device Menu 173
- LogBook Monitor 174
- Explorer 175
- Tools Menu 176
- 989592 LogView LV-51 177
- Merging Binary Data 178
- View Data 179
- Indicators Menu 180
- Digital 181
- Meters Configuration 181
- Enable Input Reading Column 183
- Appendix A A 185
- 1 = “Base” unit 192
- 0 = “Remote” unit (default) 192
- Set for 115200 192
- Error Codes 195
- Hardware Errors 196
- 878394 DD-1 197
- 878394 Dimensional Drawings 198
- 878394 DD-3 199
- 878394 DD-5 201
- 878394 DD-7 203
- 878394 DD-9 205
- DBK200 Series Boards 206
- 878394 DD-11 207
- 878394 DD-13 209
- 878394 DD-15 211
- 878394 DD-17 213
- POD-1 (for DBK83) 215
- 878394 DD-21 217
- Glossary 219
- 887199 Glossary xiii 221
Produits connexes et manuels pour Matériel Measurement-computing LogBook Series
(91 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels