Measurement-computing Data Acquisition Systems rev.10.4 Manuel d'utilisateur Page 199
- Page / 366
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Returns
DerrNoError No error
Function Usage
The term waveform/pattern output is used extensively throughout the entries for the
functions of the form daqDac…. This refers to an analog waveform output modes and/or
digital pattern output modes. These terms describe output to digital-to-analog converter
(DAC) channels and/or digital input/output (DIO) channels that are synchronously
updated by a clock source defined by the application.
The daqDacWaveGetFreq function returns the frequency via the freq parameter, The frequency is
dependent upon the clock source chosen for the selected device (see daqDacWaveSetClockSource. The
freq parameter is a pointer to a single-precision floating point variable that must be allocated by the calling
application. The waveform/pattern output update frequency is programmed with the daqDacWaveSetFreq
function.
The returned frequency value (freq) will not be valid until the waveform is armed with the
daqDacWaveArm function.
Getting the Actual Output Update Frequency
The frequency programmed using the daqDacWaveSetFreq function may not be obtainable. The reason
for this is that either the frequency specified was outside of the operating update frequency of the output pacer
clock, or the frequency is not attainable due to the resolution of the pacer clock. If the latter is the case, then
the output pacer clock will be programmed to the nearest attainable frequency. If the frequency is outside of
the operating range of the pacer clock, then an error will be generated. See the daqDacWaveGetFreq
function for more information on the actual setting of the output pacer clock frequency.
The specifications section of the device user’s manual provides the frequency settings for the device.
Prototypes
C/C++
daqDacWaveGetFreq(DaqHandleT handle, DaqDacDeviceType deviceType, DWORD
chan, PFLOAT freq);
Visual BASIC
VBdaqDacWaveGetFreq&(ByVal handle&, ByVal deviceType&, ByVal chan&, freq!)
Program References
None
Programmer’s Manual 908494 Daq API Command Reference 4.4-17
- *372195A-01* 1
- How to use this Manual 3
- 908494 Programmer’s Manual 4
- Table of Contents 5
- Introduction 1 7
- Language Support 8
- Driver Installation 9
- 908494 Programmer’s Manual 10
- Data Acquisition Environment 11
- Signal Environment 12
- 988594 Programmer’s Manual 14
- For x% = 0 To 3 30
- 0, 0, x%, bitVal&) 30
- Next x% 30
- Zero Compensation 33
- Linear Conversion 35
- End Sub 36
- Using Multiple Devices 3 37
- Internal Clock Method 40
- Master Clock Method 41
- External Clock Method 43
- Overview 45
- 938395 Programmer’s Manual 46
- Mask and Flag Definitions 50
- 961 962 963 ... 999 59
- 941 942 ... 958 959 960 59
- Raw Data Formats 81
- Setting the Scan Rate 89
- Scan Rate Mode 89
- Scan Rate State 90
- Actual Scan Rate 90
- 94
- DBK16-Read Offset Trimpot 95
- DBK43-Read Offset Trimpot 96
- Typical flags Settings 100
- Settings 101
- Prototypes 102
- Program References 102
- Function Usage 104
- Visual BASIC 105
- Returns 114
- Data Transfer Progress 115
- Example Acquisition States 116
- DazcNone 124
- DazcAutoZero 124
- Parameter Type Description 129
- Definition Description 129
- Purpose 131
- Offset value to apply 142
- Parameter Values 144
- parameters 148
- Parameter Summary 150
- Parameter Type Definitions 150
- Moving Averages 160
- Definition Description 165
- Using Thermocouples (T/Cs) 172
- T/C Gains Settings 173
- Daq/2000 Series devices* 174
- Setting the Output Mode 184
- Buffer Management 201
- DAC0 DAC1 DAC2 DAC3 P3 DO 202
- DAC0 DAC2 P3 DO 202
- Note 1: 206
- Offset for header in bytes 208
- Update Cycle Data Blocks 211
- Update/Sample Data Format 212
- Output From File Operation 212
- DaqBoard/2000c Series 219
- Setting the DAC Value 227
- 908794 Programmer’s Manual 232
- (continued) 249
- DdiProtocolInfo 251
- DdiExtFeatures 251
- Local I/O 262
- Expansion I/O 262
- Local I/O 266
- 957193 Programmer’s Manual 280
- (for 14 sample settings 282
- 2, 4, 8, 16, 32, 64 282
- 128, etc. up to 16384) 282
- Option Value (optionValue) 284
- Counter Mode 285
- 908594 Programmer’s Manual 286
- Set the Excitation Source 289
- DmotWbk14ExcSrcApply 289
- Sets the Dac Offset 290
- Use DC coupling when 290
- Example: 291
- DcovWbk17Mode_Period 295
- DcovWbk17Mode_Pulsewidth 296
- DcovWbk17Mode_Timing 296
- DcovWbk17Mode_Encoder 296
- Setting the Trigger Level 306
- API Error Codes - daqError 319
- A2 - 162 331
- Programmer’s Manual 332
- Appendix A A 333
- 988294 Programmer’s Manual 334
- 939198 Programmer’s Manual 336
- Custom OEM Installation C 337
- WIN 9x/Me WIN NT/2000/XP 338
- WIN 9x/Me and 338
- WIN NT/2000/XP 338
- Installation Locations: 339
- 958293 Programmer’s Manual 340
- 938295 Programmer’s Manual 342
- Format 347
- Time-of-Day Configuration 356
- Glossary 359
- 986896 Programmer’s Manual 360
- 986896 Glossary G-3 361
- 986896 Glossary G-5 363
- 986896 Glossary G-7 365
Produits connexes et manuels pour Matériel Measurement-computing Data Acquisition Systems rev.10.4
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels