Measurement-computing USB-1608HS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Measurement-computing USB-1608HS. Measurement Computing USB-1608HS User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 2 - USB-1608HS

10 Chapter 2 Installing the USB-1608HS What comes with your USB-1608HS shipment? As you unpack your USB-1608HS, verify that the following components

Page 3 - HM USB-1608HS.doc

USB-1608HS User's Guide Installing the USB-1608HS 11 Additional documentation In addition to this hardware user's guide, you should also re

Page 4

USB-1608HS User's Guide Installing the USB-1608HS 12 If the ACT LED turns off If the ACT (active) LED lights up but then turns off, the computer

Page 5 - Table of Contents

13 Chapter 3 Functional Details Theory of operation - analog input acquisition modes The USB-1608HS can acquire analog input data in two basic modes

Page 6

USB-1608HS User's Guide Functional Details 14 USB active LED (ACT) The ACT LED indicates the communication status of the USB-1608HS. The table b

Page 7 - About this User's Guide

USB-1608HS User's Guide Functional Details 15 Power connector Connect the external power adapter (MCC part number PS-5V2AEPS) to the power conne

Page 8 - Introducing the USB-1608HS

USB-1608HS User's Guide Functional Details 16 The following image shows a voltage source connected to a USB-1608HS configured for single-ended m

Page 9 - Software features

USB-1608HS User's Guide Functional Details 17 The following image depicts a Wheatstone bridge signal source connected to a USB-1608HS configured

Page 10 - Installing the USB-1608HS

USB-1608HS User's Guide Functional Details 18 You can use the USB-1608HS digital I/O terminals to detect the state of any TTL-level input. Refer

Page 11 - Installing the hardware

USB-1608HS User's Guide Functional Details 19 SYNC terminals (SYNC_IN and SYNC_OUT) You can use the SYNC_IN connection to externally pace the A/

Page 12 - Calibrating the USB-1608HS

USB-1608HS USB-based High-Speed Analog Input and Digital I/O Module User's Guide Document Revision 4, September, 2009 © Copyright 2009, Measur

Page 13 - Functional Details

USB-1608HS User's Guide Functional Details 20 Trigger above, level-sensitive The acquisition begins when the TRIG_IN signal is above the thresho

Page 14 - Main connector and pin out

USB-1608HS User's Guide Functional Details 21 Trigger above, edge-sensitive The acquisition begins the first time the TRIG_IN signal goes above

Page 15 - Power connector

USB-1608HS User's Guide Functional Details 22 Retrigger The acquisition uses the trigger settings for positive edge/negative edge and level-sens

Page 16

23 Chapter 4 Specifications Typical for 25 °C unless otherwise specified. Specifications in italic text are guaranteed by design. Analog input Table

Page 17

USB-1608HS User's Guide Specifications 24 Note 1: The maximum differential non-linearity specification applies to the entire 0-55 °C temperatu

Page 18 - Counter terminal (CTR)

USB-1608HS User's Guide Specifications 25 Digital input/output Table 6. Digital I/O specifications Digital type 5 V CMOS Number of I/O 16 Conf

Page 19 - Trigger terminal (TRIG_IN)

USB-1608HS User's Guide Specifications 26 External clock input/output Table 8. External clock I/O specifications Parameter Conditions Specificat

Page 20

USB-1608HS User's Guide Specifications 27 Microcontroller Table 11. Microcontroller specifications Type High performance 8-bit RISC microcontrol

Page 21

USB-1608HS User's Guide Specifications 28 Mechanical Table 16. Mechanical specifications Card dimensions 203.2 mm (L) x 121.9 mm (W) x 20.0 mm (

Page 22 - GND terminals

USB-1608HS User's Guide Specifications 29 Table 19. Main connector pin out, 8-channel single-ended mode Pin Signal name Pin Signal name 1 GND 28

Page 23 - Specifications

3 HM USB-1608HS.doc Your new Measurement Computing product comes with a fantastic extra — Management committed to your satisfaction! Thank you for ch

Page 24 - Analog input calibration

Declaration of Conformity Manufacturer: Measurement Computing Corporation Address: 10 Commerce Way Suite 1008 Norton, MA 02766 USA Category

Page 25 - External trigger

Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: [email protected]

Page 26 - Counter

4 Trademark and Copyright Information TracerDAQ, Universal Library, Measurement Computing Corporation, and the Measurement Computing logo are either

Page 27

5 Table of Contents Preface About this User's Guide ...

Page 28 - Mechanical

USB-1608HS User's Guide 6 Power ...

Page 29

7 Preface About this User's Guide What you will learn from this user's guide This user's guide explains how to install, configure, and

Page 30 - Declaration of Conformity

8 Chapter 1 Introducing the USB-1608HS This user's guide contains all of the information you need to connect the USB-1608HS to your computer and

Page 31

USB-1608HS User's Guide Introducing the USB-1608HS 9 USB-1608HS block diagram USB-1608HS functions are illustrated in the block diagram shown he

Commentaires sur ces manuels

Pas de commentaire