Measurement-computing CIO-EXP-GP Manuel d'utilisateur Page 3
- Page / 46
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Table of Contents
17
5.4 Determining the Appropriate Gain
..........................................
17
5.3.3 Adding a Ground Reference
.............................................
15
5.3.2 Enabling Open Thermocouple Detection (OTD)
...........................
15
5.3.1 Setting the Input Configuration
..........................................
15
5.3 Input Configuration
.......................................................
14
5.2 Selecting The CJC Output Channel
.........................................
14
5.1 Selecting The Output Channel
..............................................
14
5 CONFIGURATION FOR THERMOCOUPLE MEASUREMENT
.................
13
4.8 Verifying the Installation
...................................................
12
4.7.3 Fully Differential
......................................................
12
4.7.2 Floating Differential
...................................................
12
4.7.1 Single-Ended Inputs
...................................................
11
4.7 Connecting Voltage Signals
................................................
11
4.6 Setting the Input Configuration
.............................................
10
4.5 Attenuation
...............................................................
10
4.4.2 Setting Channel Gain
..................................................
9
4.4.1 Setting Board Gain
.....................................................
9
4.4 Setting the Gain
............................................................
8
4.3 Determining The Appropriate Gain
..........................................
8
4.2 Powering the CIO-EXP-GP
.................................................
8
4.1 Channel Selection
..........................................................
8
4 CONFIGURATION FOR VOLTAGE MEASUREMENT
...........................
7
3.8 Verifying the Installation
....................................................
6
3.7 Connecting a Test Voltage
..................................................
6
3.6 Daisy-Chaining CIO-EXP-GP Boards
........................................
5
3.5.4 Powering Through the Power Screw Terminals:
.............................
5
3.5.3 Powering with the Molex Connector
......................................
5
3.5.2 Powering with the 37-Pin Connector
......................................
5
3.5.1 Power Source Switch
...................................................
5
3.5 Powering The CIO-EXP-GP
.................................................
4
3.4.3 Other A/D Boards
......................................................
4
3.4.2 Connecting to a DAS16 Series A/D Board
.................................
4
3.4.1 Connecting to a DAS08 Series A/D Board
.................................
4
3.4 CONNECTING THE CIO-EXP-GP TO THE A/D BOARD
....................
3
3.3.3 All A/D Boards
........................................................
3
3.3.2 DAS16 Family Setup
...................................................
3
3.3.1 DAS08 Family Setup
...................................................
3
3.3 Configuring the A/D Board
..................................................
2
3.2 Setting The Output Channel
.................................................
2
3.1 A/D Board Type Select Jumper
..............................................
2
3 GENERAL CONFIGURATION
..................................................
1
2 SOFTWARE INSTALLATION
..................................................
1
1 INTRODUCTION
..............................................................
- CIO-EXP-GP 1
- User’s Manual 1
- HM CIO-EXP-GP.lwp 2
- Table of Contents 3
- 1 INTRODUCTION 5
- 2 SOFTWARE INSTALLATION 5
- 3 GENERAL CONFIGURATION 6
- 3.3 Configuring the A/D Board 7
- 3.3.1 DAS08 Family Setup 7
- 3.3.2 DAS16 Family Setup 7
- 3.3.3 All A/D Boards 7
- 3.4.3 Other A/D Boards 8
- 3.5 Powering The CIO-EXP-GP 9
- 3.5.1 Power Source Switch 9
- 4.1 Channel Selection 12
- 4.2 Powering the CIO-EXP-GP 12
- 4.4 Setting the Gain 13
- 4.4.1 Setting Board Gain 13
- 4.4.2 Setting Channel Gain 14
- 4.5 Attenuation 14
- IN CONFIG 15
- 4.7.1 Single-Ended Inputs 16
- 4.7.2 Floating Differential 16
- 4.7.3 Fully Differential 16
- - THERMOCOUPLE LEAD 20
- + THERMOCOUPLE LEAD 20
- 5.5 Setting the Gain 22
- 5.5.1 Setting the Board Gain 22
- Output Gain Switch 22
- Channel Gain Switches 23
- 6.1 Channel Selection 24
- 6.2 VEXC JUMPER Select 24
- 6.3 CJC Jumper Selection 24
- 6.4 Powering the CIO-EXP-GP 24
- 6.6 Setting the Gain 26
- 6.6.1 Setting the Board Gain 26
- 6.8.1 Two-Wire RTD Hookup 28
- 6.8.2 Three-Wire RTD Hookup 28
- 6.8.3 Four-Wire RTD Hookup 28
- +5V Excitation Voltage Source 31
- 7.6 Setting the Gain 32
- 7.6.1 Setting the Board Gain 33
- A Half Bridge Example 38
- Half Bridge Calculations 38
- 8 SPECIFICATIONS 40
- 9 APPENDIX 42
- For your notes 44
- EC Declaration of Conformity 45
Produits connexes et manuels pour Matériel Measurement-computing CIO-EXP-GP
(32 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels